Needs - Your Resource for Health and Wellness
Call Toll Free: 1.800.634.1380
Listen and Learn
Teleseminar Speaker "How to Corona-Proof Your Life Follow Up" with Dr. Sherry Rogers.
About TransFirst®
Card Acceptance
Doctor's Best Authorized Online Retailer

Safecoat MexeSeal - Gloss Finish Enlarge Image Email to a Friend AFM
Safecoat MexeSeal - Gloss Finish
ITEM NUMBER:    AFM-6042-128
SIZE:    128 Fluid Ounces
Your Price: Due to its weight, this product carries an additional shipping surcharge of $3.00.

Product Description: Safecoat MexeSeal is a low odor, water based, medium gloss clear sealer. It is suitable for use on porous tile or masonry surfaces where a durable oil and water resistant finish is desired. It is ideal for long term protection against food, oil and water stains on residential or commercial floors. Safecoat MexeSeal is non-hazardous and non-flammable - a total replacement for high solvent content systems.
Use On: Safecoat MexeSeal is recommended on substrates such as the following: limestone, unpolished granite, sandstone, slate, fireclay (brick, tile, terra cotta, pavers), unglazed tile, concrete (brick, tile, precast panels, cast in place). Always test in small, inconspicuous places before full application. Safecoat MexeSeal is generally not suited for polished surfaces. Not recommended for use on modern satillo or quarry tiles without special care. Satillo or quarry tiles generally contain salts and other contaminants sensitive to application of water based products. White efflorescence flushing may occur. It may be necessary to repeatedly remove contamination and repeat MexeSeal application until all contaminants are extracted.

Warnings: Health Precautions: As with all coatings and sealers, keep container tightly closed and out of the reach of children. Do not take internally. Keep from freezing. Always use adequate ventilation. If you are chemically sensitive, always test for personal tolerance.

Additional Info: Limitations: Unlike most conventional sealers, Safecoat is made without formaldehyde preservatives. Do not contaminate. Keep from freezing. Not for surfaces which may be subject to standing water. Not tested on animals.
Limited Warranty: Safecoat products are guaranteed not to be defective when applied and used in accordance with instructions. However, liability, whether express or implied, is limited to replacement of product or refund of purchase price and cannot include liability for labor costs or consequential damages. Because of the varying circumstances affecting each job, including environmental factors, possible surfaces and application techniques, and the lack of control we have over such matters, it is the user's responsibility to determine the suitability and safety of the product for any particular application. We particularly recommend that users always test in small inconspicuous areas before application to the entire surface.

Packaging: White Plastic
Does Not Contain: Animal Ingredients.
Suggested Use: Surface Preparation: All surfaces must be clean, dry, free from dirt, dust, efflorescence, grease, wax, oil, silicone, tsp/soap, mill scale, oxidation, loose peeling paint or varnish, or any foreign matter/contaminants. Remove all mildew before coating any surface. When acid has been used for any reason, surface must be completely neutralized.
Application: Always have adequate ventilation. Stir gently. Do not shake container (shaking causes air bubbles). Apply only in thin even coats, using sponge, brush, pad or appropriate spray equipment. Only if necessary, may be thinned with up to 10% water for spraying. Do not use a roller or rayon mop. Allow one hour to dry between coats, depending upon conditions. Two or more coats may be needed depending on porosity of masonry. Close surface to traffic after application and until completely dry.
Coverage: One gallon covers approximately 300 square feet in one coat depending on surface porosity.
Clean-Up: Clean tools and equipment while they are still wet with a solution of SafeChoice Super Clean and warm water.
Drying/Curing Time: Under normal conditions, Safecoat MexeSeal dries to touch in one hour, is recoatable after two hours and may be opened to traffic after 8-24 hours. Normal conditions include a clean, dry surface, access to fresh air flow, a dust free environment, moderate humidity, and temperatures above 55° F. Thick application, high humidity or conditions other than normal will cause Safecoat MexeSeal to dry and cure more slowly. Surface should remain water-free for at least 72 hours while curing.
Maintenance: Mop floor periodically with clean water or an odorless, dye-free, non-volatile all purpose cleaner like SafeChoice Super Clean. May be scrubbed with white pad and 175 RPM floor machine before recoating.