Needs - Your Resource for Health and Wellness
Call Toll Free: 1.800.634.1380
Facebook
Blog
Twitter
Twitter
Twitter
spacer
Listen and Learn
Teleseminar Speaker Laurel Sterling, MA, RDN, CDN,
spacer
About TransFirst®
Card Acceptance
Shipping
Doctor's Best Authorized Online Retailer


Safecoat Polyureseal BP - Gloss Enlarge Image Email to a Friend AFM
Safecoat Polyureseal BP - Gloss
ITEM NUMBER:    AFM-5032-128
SIZE:    128 Fluid Ounces
Your Price: Due to its weight, the 128 FlOz size carries an additional shipping surcharge of $3.00.
Qty:  

Product Description: Safecoat Polyureseal BP is one of the highest quality low toxicity water-based clear gloss finishes available today. Its exceptional durability and abrasion resistance, coupled with high solids, very low VOC and low odor, make it the clear alternative to conventional solvent and water-based polyurethanes in performance without the toxicity.
Safecoat Polyureseal BP can be used on unfinished (or properly prepared and sanded previously finished) wooden surfaces such as floors, furniture and cabinetry, and is excellent for gym floors and auditoriums.
Doctor recommended, non toxic. Conforms to ASTM - D2047 test for slip resistance. Water based. Wood & floor. Were the best sealer choice for personal health - especially for the chemically sensitive - and we're proud to be one of the only doctor recommended sealers on the market. You'll breathe easier knowing that our unique formulation helps block toxic emissions from seeping into your environment. Plus, our premium quality produces beautiful results. You don't have to give up style for health. No animal testing - ever.

Warnings: Health Precautions: As with all coatings and stains, keep container tightly closed and out of the reach of children. Do not take internally. Always use adequate ventilation. Wear a mask when sanding and avoid breathing sanding dust. Avoid contact with skin and eyes and avoid breathing of spray vapors and spray mist. If you are chemically sensitive, always test for personal tolerance.
Additional Info: Limitations and Limited Liability: See technical advisory at http://www.afmsafecoat.com/products.php?page=3.
Packaging: White Plastic
Suggested Use: Surface Preparation: All surfaces must be clean and free from dirt, dust, grease, wax, oil, silicone, tsp/soap, mill scale, oxidation, loose peeling paint or varnish, or any foreign matter/contaminants. Apply test patches before undertaking large areas to assure good adhesion and lack of surface contamination. Wood staining should be completed before applying finish coats. Sand wood with the grain only. When surfaces have been sanded, dust and vacuum thoroughly to remove debris and then use a damp rag to remove dust before applying finish coats. (Note: Do not use tac rags.) Wood surface may be dampened to raise grain, sanded, and then wiped free of dust before applying stain or finish. Moisture content of wood should be below 12% for best results. To achieve best results on wood, apply multiple thin coats of Safecoat Polyureseal BP Gloss until the surface is completely sealed, followed by one final coat of Satin.
Application: Before using, mix coating thoroughly by gently stirring or rolling container to avoid air bubbles. Be sure to stir product thoroughly every 20 minutes during application. Intermix (boxing) all containers of the same sheen to ensure gloss uniformity before applying. Do not shake container. Pour material to be used into another container before applying coating to avoid contaminating main container. Then apply as is, using a quality nylon brush, pad applicator, or unheated spray applicator. Apply liberal coats, keeping a good wet edge and avoid over brushing. In most cases, a minimum of 3 coats is required, depending on the surface. When spraying, use a .015 tip or smaller. Apply thin, even coats when spraying rather than heavy coats which will tend to sag. If spray pattern begins to dryspray, reduce air pressure and increase material flow to surface. Use a damp, dust free rag after sanding to remove dust particles. Use aluminum oxide or silicon carbide sandpaper to sand between coats. For best results, this product should not be reduced. Use only during low or moderate humidity conditions. Applying this product over lightly dampened surfaces can assist the user in controlling the dry time. Smoother finishes are achieved when surfaces are damp during application. Note: The applicator should determine which preparation and techniques are best suited to the specific surface. Precautions: Contaminants on floors can cause floors to become slippery.
Coverage: One gallon of Safecoat Polyureseal BP covers approximately 350 square feet in one coat depending on method of application and surface porosity.
Clean-Up: Clean tools and equipment while they are still wet with a solution of SafeChoice Super Clean and warm water.
Drying/Curing Time: Under normal conditions, Safecoat Polyureseal BP dries to touch in 1 hour, is sandable after 2-4 hours, and is re-coatable after 4-8 hours. The product will continue to cure and become harder over time. Avoid traffic for at least 24 hours after application. Normal conditions include a dry surface, access to fresh airflow, moderate humidity, and temperatures around 70 degrees F. Thick application, high humidity or conditions other than normal will cause Safecoat Polyureseal BP to dry and cure more slowly.
Maintenance: Damp mop or wipe coated surface periodically with clean water or an non-volatile all purpose cleaner like SafeChoice Super Clean.


Related Products
Safecoat Polyureseal BP - Gloss